Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum deflection with consideration of initial slippage.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Je prostě podepřený. The problem is described using the following parameters. Determine the deflections in the given test times.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Porovnejte průhyby rohů desek pro kontrolu správnosti transformace.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Spřažená deska sestávající ze tří skleněných vrstev, jedné vrstvy fólie a vnitřního prostoru se suchým vzduchem je plně upevněna a zatížena proměnnou teplotou. Neglecting its self-weight, determine the plate's maximum deflection.
Konzola je plně fixována na levém konci a zatížena příčnou silou a normálovou silou na pravém konci. The tensile strength is zero and the behavior in the compression remains elastic.
Dvouvrstvá silnostěnná nádoba s otevřeným koncem je zatížena vnitřním a vnějším tlakem; proto nevzniká žádné osové napětí. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
Dokažte, že spojení různých rozměrových prvků nemá vliv na výsledky. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Silnostěnná nádoba je zatížena vnitřním tlakem tak, že nádoba dosáhne pružno-plastického stavu. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Stanoví se maximální průhyb a napětí ve směru z spřažené desky, která se skládá ze dvou skleněných vrstev a jedné vrstvy fólie mezi nimi a je vystavena konstantnímu tlaku.
Tlumený jednohmotový systém je zatížen konstantní silou. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Konzola z kruhového prutu je zatížena excentrickým rovnoměrným zatížením. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Vlastní tíhu zanedbáme. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Cílem tohoto příkladu je předvést nevratný děj způsobený třením. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
A compact disc (CD) rotates at a speed of 10,000 rpm. Je tak vystaven odstředivé síle. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Stanoví se maximální posun, napětí v rovině a poměr napětí u jednoduše podepřené dvojité skleněné desky s fólií mezi oběma skleněnými tabulemi vystavené rovnoměrnému tlaku.
Představme si spojení dvou trubek lešení, které je namáháno normálovou silou a momentem. Self-weight is not considered. The material of the tube is idealized as perfectly rigid. All geometrical non-linearities are ignored. Determine the angle of deflection.
Konzola s kruhovým průřezem je namáhána soustředěnou ohybovou silou a kroutícím momentem. The aim of this verification example is to compare the reduced stress according to the von Mises and Tresca theories.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Compare the deflections of the plate corners to check the correctness of the transformation.
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. Na rovinu procházející středem bloku působí svislý tlak.
Ve spodní části jsou upevněny čtyři sloupy, které jsou nahoře spojeny tuhým blokem. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Stanoví se přípustná pevnost v osovém tlaku kloubového nosníku o délce 2,8 m různých průřezů ze slitiny 6061-T6 a bočně vetknutého proti vybočení okolo nejslabší osy podle Aluminum Design Manual 2020.